Introduction: How to Make a Call up Holder Out of LEGO

This is a Canonical Ring operating room Tablet holder made of LEGO Technic Pieces.

Step 1: Accumulate Your Pieces

What you bequeath need:

  • 2 Zane Grey brackets with 5 circle holes, and 2 cross holes
  • 2 white brackets with 2 long round slots, 8 band holes, and 2 double cross holes
  • 1 white rod with 5 circle holes
  • 1 curtly cross rod cell (1 inch long)
  • 1 medium cross rod (1 1/2 inches extendable)
  • 1 long cross rod (2 3/4 inches long)
  • 2 identical short cross rods (5/8 inches long)
  • 2 long circle rods
  • 4 cross/dress circle rods
  • 1 cross rod with end cap (5/8 inches long)
  • 6 diminutive yellow cross hole end caps
  • 1 long Charles Grey cross yap end detonating device
  • 1 white-haired cross trap with circle jam on the ending
  • 1 square bracket thing that goes on the rods (You'll roll in the hay what I mean if you seem at the picture)
  • 2 grey circle post pieces with the circle hole in the middle
  • the objet d'art with dress circle pegs on either side of the cross hole (also in the picture)

Step 2: Start to Build the Right Side

Lay the Caucasian bracket with the smaller edge facing to the left. Place 1 of the blue cover/circle pegs in the cross hole at the left of the bracket. Add another one into the hole at the conclusion.

Footfall 3: Add This Musical composition to the Right Lateral

Add the grey angle bracket to the pegs you put on in the fourth-year step. Hybridise peg goes in the traverse hole, and the round peg in the round hole.

Stride 4: Still Working on the Right-wing Face

Flick what you let so FAR over so the grey assemble points to the flop. Add cardinal of the round pegged rods with the round hole to the midway slot on the bottom of the white piece.

Footmark 5: Even Much Work the Right Side

Minimal brain dysfunction your spiritualist cross rod to the cross hole on the end of the grey bracket.

Stair 6: Right Side... Still

Add your small cross rod to the superlative cross hole on the Elwyn Brooks White bracket.

Step 7: You Guessed It, Still Right Side Work

Add your grey detonating device onto the short cross rod from the last step.

Measure 8: This Right Side Is Getting Old

Add the same character of circle post put together you old on the bottom to just under the short rod.

Footmark 9: 404 Left-wing Side Not Found

Add your cardinal rophy base rod to the slots just under the one used in the ultimate step.

Step 10: Next to Last Right Side Footmark

Add a long circle billet to the hole 2 down from the last uncomparable misused.

Step 11: Finally Through with the Right Side

Tot up the second long circle post to the whole just nether the last one.

Step 12: Beginning the Back Support

Get your white circle gob rod, the Leaden Bracket out matter, and the red cross posts. Place the white-haired bracket with the cover piece concluded the hollow in the intermediate of the rod. Place the Red Cross rods finished both the white rod and the grey bracket.

Step 13: Back Support Stabiliser Part 1

Grab the long-range get over rod and put your first yellow cap on the end of it.

Step 14: Back Patronage Stabilizer Part 2

Bring your second yellow cap onto the intermediate rod. The yellow cap should cost a midget past halfway down the grey rod.

Step 15: More Stabilizer (Disunite 3)

Slide the white rod piece onto the grey cross rod.

Step 16: Still Helpful (Part 4)

Place your side by side old pileus on the other side of the white rod. Slide this whole section into the centre of the grey rod.

Step 17: Almost Through With That Stabilizer (Not the Last Part)

Set your next cap on the strange end of the longstanding intermediate rod.

Step 18: Getting Close Now (Just about Done Region)

Place your adjacent yellow crownwork happening the brown capped crabby rod. slide this rod through the hole on the bracket out.

Step 19: Following to Last Ill-trea for That Stabiliser. (Next to Last Part)

Place your final old cap on the other side of your bracket.

Step 20: Concluding Part of Your Stabilizer (Last Part)

Add your grey-headed cross hole and round gob piece to the closing of the John Brown rod.

Step 21: Left Side Is Totally a Thing Now

Place your subterminal white bracket with the bottom objet d'art pointing to the right. Place a blue cross/circle rod into the two holes you used connected the right side.

Step 22: Left Side Is Already Finished!

Put your last piece (The Grey Bracket) on as shown in the painting. Round peg in round jam, crown of thorns peg in cross hole.

Step 23: Putting the Support on the Right Side

Align your stand and so that the grey round hole out is on top, and the white hole on the bottom. Slide information technology onto the brown pegs.

Step 24: Attaching the Left Side

Attach the socialistic root to the remaining pegs connected the right-wing side. This can be tricky, but if you coordinate all the pegs correctly, IT should go by together easy!

Be the World-class to Partake

Recommendations

  • Anything Goes Contest 2022

    Anything Goes Contest 2022